Dammam
+919892534043
Dammam
+919892534043
+919892534043
Chat with us

Chat with us on WhatsApp

Home
products
Quote
Menu

Water Washout Tester

Grease Testing Equipment

Water Washout Tester

In stock•cod not available

Contact Us

Phone Number

+919892534043

Email Address chirag@spearexim.com

Mon-Thu: 10 AM - 2 PM • Fri: 3 PM - 7AM

Other Website Visit our other website
Address Dammam Saudi Arabia

Dammam, Saudi Arabia, 0

Description

Water Washout Tester As per ASTM D1264 The water washout apparatus is suitable for testing water washout characteristics of grease as per ASTM D1264. A sample of the lubricating grease under evaluation is tested in a bearing rotating under specific speed by spraying heated water and the loss of grease is determined. A tank is provided to hold about 750 ml of water with heating arrangement for heating the water to up to temperature 80°C. The equipment is provided with test bearing housing assembly as specified in the test method. The digital temperature controller with sensor is also provided for accurate indication of the temperature inside the equipment. The unit is provided with a ball bearing (ASTM 204) as specified in the test method. Circulating pump provided with a supply pressure and a return suction line, regulating valves, a splash nozzle and accessory.The pump is capable of delivering 300 ml/min heated water via 1mm capillary. The water containing washed out grease is collected in the tank, filtered & recycled during the test. Provision is made for fine adjustable of water flow through a bypass to allow the preheated water to circulate without passing through the jet or impinge on bearing housing. Features The bearing rotational speed is 600 ± 30 rpm. Supplied with test bearings – 2 Nos. Drain valve to remove the tested water. Provided with necessary tools and fixtures for assembling of bearing housing. Power supply : 120 V / 230 AC, Single Phase, 50 / 60 Hz

Other Products

view all

68179d65be22ee500d53ff54 Card 2

product image
Transformer Oil Testing Machine

Gassing Tendency Apparatus

As per ASTM D-2300, BS 5797:1986, IEC 628:1985 Gassing Tendency Apparatus measures the tendency of insulating oil / liquids to evolve or absorb gas when subjected in cells having specific geometrics, electrical stress of sufficient intensity to cause an electric discharge through a gas phase in which a gas oil interface is located. Fully Made with Stainless Steel Assembly Gassing cell and gas burette assembly made of borosilicate glass with a relative permittivity of 5 ± 0.2 at 80°C. Hollow high-voltage electrode-made of centre less-ground and polished stainless steel with stainless steel capillary tubing as a gas passage. The electrode is supported by PTFE Plug Constant temperature oil bath with a heating and circulation with digital temperature control system. Transparent safety shield-made of clear view acrylic sheet. Power supply : 120 V / 230 Volt AC, 1 Phase, 50/60 Hz

68179d65be22ee500d53ff54 Card 2

product image
Flowmeters

Glass Tube Rotameter

Rotameters are devices which measure the flow rate of liquid or gas in a closed tube. This product is machined from clear acrylic block and is designed to give maximum accuracy in visibility and ruggedness. The floats are made from stainless steel, PVC and other non corrosive materials. The needle valve is provided for accurate flow control. It is designed to give accuracy of 0.5 to 1% at full scale. The higher accuracy can be made on specific requirement.

68179d65be22ee500d53ff54 Card 2

product image
Flowmeters

Glass Tube Rotameter

Rotameters are devices which measure the flow rate of liquid or gas in a closed tube. This product is machined from clear acrylic block and is designed to give maximum accuracy in visibility and ruggedness. The floats are made from stainless steel, PVC and other non corrosive materials. The needle valve is provided for accurate flow control. It is designed to give accuracy of 0.5 to 1% at full scale. The higher accuracy can be made on specific requirement.